Serial ip port redirector install#
Serial ip port redirector drivers#
Serial ip port redirector software#
Serial ip port redirector code#

Set the application on the PC to use the COM/IP modem device installed on the COM/IP virtual COM port, and it will receive the incoming call that is redirected from the Cisco router. This tells the COM/IP modem to listen to port 7000 for an incoming connection. In the Init String in COM/IP add the string: ATS1008=7000

Serial ip port redirector install#

On the PC (10.0.0.1) install COM/IP and the COM/IP modem driver. The configuration on the Cisco router to accomplish this on line 1 is: autocommand telnet 10.0.0.1 7000 /streamĮscape-character NONE (if using an AS5350 or 5400)įor each incoming line redirected through COM/IP, the line 'autocommand telnet /stream' will need to be added to a separate line in the Cisco configuration. The first step is to configure the Cisco to make a raw TCP/IP connection to a PC when the call comes to a specific modem.Įxample: If PC's IP address is 10.0.0.1 and the TCP port will be 7000. Please note that DialOut/EZ is still required to make outbound calls. Receiving an inbound call with a Cisco router that has digital modems is possible with Tactical Software's COM/IP program. If DialOut/EZ doesn't have a active reverse telnet session to the modem, then the application on the user's PC can not see that the modem is ringing and thus can not answer it. When this box is checked, HyperTerminal will remove characters (including the 'X') that it doesn't consider to be part of the phone number.Ĭisco routers with digital modems (Mica, NextPort) are not able to support dial-in back through DialOut/EZ, as they are not able to answer an incoming call while there is an active reverse telnet session to them. Now when a call is made the 'X' character will be sent through.

Serial ip port redirector code#

Microsoft TAPI can strip out characters in a dial string and in some cases the 'X' character can be removed.įor example: In HyperTerminal, go to File | Properties and uncheck the 'Use country/region code and area code' checkbox. To dial the phone number 1234567890, pause for 15 seconds and then dial 12345, the dial string needs to be 1234567890X,12345 Rotary 1 ! use TCP port 7001 to dial out rotary 1ĪS5350 note: Make sure the line 'escape-character NONE' is in the Line Config.Ĭisco routers with digital modems require that an 'X' character be placed in front of any DTMF data (dual tone multi-frequency) that is sent in a dial string after a phone number. Modem inout ! if dialout ONLY, use 'modem dtr-active'

Line 'begin' 'end' ! replace 'begin/end' with first/last lines The IOS configuration under the 'line' section of the configuration file should be:

Serial ip port redirector drivers#

The client machines will need to have the correct modem drivers installed. Our products will continue to require that network endpoints be specified using IPv4 addresses, or hostnames which resolve to IPv4 addresses.Ĭisco IOS version 12.1(8) or greater is required.

Serial ip port redirector software#

Therefore, Tactical Software will not be incorporating direct support for connecting to network endpoints using IPv6 addresses and has decided to continue using IPv4 in its products. Until the last device and piece of software that requires IPv4 is removed from a network (including any external devices/systems that interact with it), there will be a need for the network to support IPv4 in addition to IPv6. While updating to a IPv6-based network is mandated or needed in some cases, these networks will be required to also support IPv4 for the foreseeable future. Anyone upgrading their network to be IPv6-compliant will not encounter issues with Tactical Software's products, as IPv4 connectivity will still be needed for many other devices and software on the network. The few devices that support IPv6, do so in addition to IPv4, maintaining backward compatibility. Many of these devices are legacy systems which will never support IPv6. Tactical Software's products are deployed in environments with devices that support IPv4-only.

Tactical Software has successfully tested its products in a variety of network environments and Windows versions which include both IPv6 and IPv4 addressing.

All versions of Microsoft Windows which support IPv6 are dual stack, meaning they can operate in both IPv6 and IPv4 networks.